PRODUCT NAME: UVIBOND™
SL-Lo
CHEMICAL FAMILY: Unfilled
urethane acrylate/monomer blend
| Chemical Identity | Cas # | %, wt | Exposure Limits/TLV |
| 1. Proprietary acrylated urethane oligomer | N/A | 65-80 | NE |
| 2. Acrylate monomer | 13048-33-4 | 5-15 | NE |
| 3. Vinyl terminated monomer blend | Proprietary | 10-30 | NE |
| All ingredients used to make the product are listed on the TSCA Inventory and are not considered hazardous. | |||
| None of these chemicals are considered to be carcinogenic by NTP, IARC, or OSHA. Abbreviations: | |||
| NE - not established NA - not available/not applicable ppm - parts per million |
|||
| H.M.I.S. Rating: Health - 2 Flammability - 1 Reactivity - 1 | |||
BOILING POINT: 100°C
SPECIFIC GRAVITY: (water
= 1): 1.13
VAPOR PRESSURE: < 0.01
mm Hg @ 25°C
VAPOR DENSITY (air =
1): Not determined
EVAPORATION RATE (Butyl
Acetate = 1): Nil
SOLUBILITY IN WATER:
Partially soluble
PERCENT VOLATILE BY VOLUME:
Negligible
APPEARANCE AND ODOR:
Clear straw (SL-Lo) or milky (SL-Hi), low viscosity liquid; mild characteristic
acrylate odor.
FLASH POINT (method):
> 100°C (closed cup)
FLAMMABLE LIMITS: LEL
- Unknown UEL - Unknown
EXTINGUISHING MEDIA: C02,
dry chemical, foam or water spray
SPECIAL FIREFIGHTING PROCEDURES:
Burning will produce toxic fumes; wear self-contained breathing apparatus and
full protective gear.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
High temperatures and fire conditions may cause rapid and uncontrolled polymerization
which can result in explosions and the violent rupture of storage vessels or
containers. Avoid use of a stream of water to control fires since frothing can
occur.
STABILITY: Unstable
INCOMPATIBILITY (materials
to avoid): Polymerization initiators including peroxides, strong oxidizing agents,
copper, copper alloys, carbon steel, iron, rust and strong bases, HAZARDOUS
DECOMPOSITION OR BYPRODUCTS: Acrid smoke-carbon monoxide/ carbon
dioxide fumes may be released during a fire.
HAZARDOUS POLYMERIZATION:
May occur.
CONDITIONS TO AVOID: Heat,
oxidizing conditions, ultraviolet light, inert gas blanketing.
SKIN: May cause moderate skin injury (reddening and swelling) and/or sensitization. Prolonged contact may cause blister formation (burns). Since irritation may not occur immediately, contact can go unnoticed.
EYES: Moderate to severe irritant; may cause chemical burn in eyes--damage irreversible.
INHALATION: No expected hazard, however use in well ventilated area.
INGESTION: Practically nontoxic
TARGET ORGANS: None known EMERGENCY FIRST AID PROCEDURES:
SKIN: Remove contaminated clothing. Wash skin thoroughly with mild soap/water. EYES: Rinse with clean water for 20-30 minutes. Retract eyelids often while rinsing. Seek medical attention
INHALATION: In case of exposure to a high concentration of vapor or mist, remove person to fresh air. If breathing has stopped, administer artificial respiration and seek medical attention.
INGESTION: If appreciable quantities are swallowed, seek medical attention.
SPILL OR LEAK PROCEDURES:
Blanket with firefighting foam. Cover with inert, absorbent material and remove
to disposal container.
WASTE OR DISPOSAL METHOD:
Follow all federal, state, and local regulations.
RECOMMENDED STORAGE CONDITIONS: Store indoors at 20-25°C in original,
unopened containers. Do not blanket containers with dry N2 or Argon. Oxygen/air
blanket recommended.
RESPIRATORY PROTECTION:
When exposed to aerosols or vapors, use full face organic vapor cartridge respirator
with particulate pre-filter. In emergency situations, or when used in confined
spaces, use self-contained breathing apparatus or other air supplied full-face
respirator.
VENTILATION: Local exhaust
recommended to control exposure which may result from operations generating
aerosols and hot operations generating vapors.
PROTECTIVE GLOVES: Impervious
(Neoprene)
EYE PROTECTION: Chemical
splash goggles or full face shield
OTHER PROTECTIVE EQUIPMENT:
Eye wash facilities; safety shower
This product contains the following toxic chemical(s) subject to the reporting requirements of section 313 of title III. of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR part 372: None The data contained herein are based on information believed to be reliable. No warranty, expressed or implied, regarding the accuracy of this information will be given. It is intended that the buyer and user of these products shall determine the suitability of the information provided for his specific application, and is responsible for its selection. Purchasers assume all risk and liability whatsoever in connection with the use of these products and this information.
UVIBONDT is a registered trademark of Aptek Laboratories, Inc.
HOME | UVIBOND SL-Lo | UVIBOND SL-Hi | UVIFILL SL-Tx | APTEK Repair Resin