PRODUCT NAME: UVIBOND™ SL-Hi
CHEMICAL FAMILY: Unfilled urethane acrylate/monomer blend

BOILING POINT: > 100°C
SPECIFIC GRAVITY: (water = 1): 1.13
VAPOR PRESSURE: < 0.01 mm Hg @ 25°C
VAPOR DENSITY (air = 1): Not determined
EVAPORATION RATE (Butyl Acetate = 1): Nil
SOLUBILITY IN WATER: Partially soluble
PERCENT VOLATILE BY VOLUME: Negligible
APPEARANCE AND ODOR: Clear straw (SL-Lo) or milky (SL-Hi), low viscosity liquid; mild characteristic acrylate odor.

FLASH POINT (method): > 100°C (closed cup)
FLAMMABLE LIMITS: LEL - Unknown UEL - Unknown
EXTINGUISHING MEDIA: C02, dry chemical, foam or water spray
SPECIAL FIREFIGHTING PROCEDURES: Burning will produce toxic fumes; wear self-contained breathing apparatus and full protective gear.
UNUSUAL FIRE AND EXPLOSION HAZARDS: High temperatures and fire conditions may cause rapid and uncontrolled polymerization which can result in explosions and the violent rupture of storage vessels or containers. Avoid use of a stream of water to control fires since frothing can occur.

STABILITY: Unstable
INCOMPATIBILITY (materials to avoid): Polymerization initiators including peroxides, strong oxidizing agents, copper, copper alloys, carbon steel, iron, rust and strong bases,
HAZARDOUS DECOMPOSITION OR BYPRODUCTS: Acrid smoke-carbon monoxide/ carbon dioxide fumes may be released during a fire.
HAZARDOUS POLYMERIZATION: May occur.
CONDITIONS TO AVOID: Heat, oxidizing conditions, ultraviolet light, inert gas blanketing.

SKIN: May cause moderate skin injury (reddening and swelling) and/or sensitization. Prolonged contact may cause blister formation (burns). Since irritation may not occur immediately, contact can go unnoticed.
EYES: Moderate to severe irritant; may cause chemical burn in eyes--damage irreversible.
INHALATION: No expected hazard, however use in well ventilated area.
INGESTION: Practically nontoxic

TARGET ORGANS: None known

EMERGENCY FIRST AID PROCEDURES:

SKIN: Remove contaminated clothing. Wash skin thoroughly with mild soap/water.
EYES: Rinse with clean water for 20-30 minutes. Retract eyelids often while rinsing. Seek medical attention
INHALATION: In case of exposure to a high concentration of vapor or mist, remove person to fresh air. If breathing has stopped, administer artificial respiration and seek medical attention.
INGESTION: If appreciable quantities are swallowed, seek medical attention.

SPILL OR LEAK PROCEDURES: Blanket with firefighting foam. Cover with inert, absorbent material and remove to disposal container.
WASTE OR DISPOSAL METHOD: Follow all federal, state, and local regulations.
RECOMMENDED STORAGE CONDITIONS: Store indoors at 20-25°C in original, unopened containers. Do not blanket containers with dry N2 or Argon. Oxygen/air blanket recommended.

RESPIRATORY PROTECTION: When exposed to aerosols or vapors, use full face organic vapor cartridge respirator with particulate pre-filter. In emergency situations, or when used in confined spaces, use self-contained breathing apparatus or other air supplied full-face respirator.
VENTILATION: Local exhaust recommended to control exposure which may result from operations generating aerosols and hot operations generating vapors.
PROTECTIVE GLOVES: Impervious (Neoprene)
EYE PROTECTION: Chemical splash goggles or full face shield
OTHER PROTECTIVE EQUIPMENT: Eye wash facilities; safety shower

RCRA Status:

This product as supplied is not regulated as hazardous waste under RCRA (40 CFR 261). It is the responsibility of the product user to determine at the time of disposal, whether a material derived from this product has become a hazardous waste.

The data contained herein are based on information believed to be reliable. No warranty, expressed or implied, regarding the accuracy of this information will be given. It is intended that the buyer and user of these products shall determine the suitability of the information provided for his specific application, and is responsible for its selection. Purchasers assume all risk and liability whatsoever in connection with the use of these products and this information.

Revised: 02/11/10 - jv Issued: 06/08/98
APTEK® is a registered trademark of Aptek Laboratories, Inc.
UVIBOND™ is a registered trademark of Aptek Laboratories, Inc.

HOME | UVIBOND SL-Lo | UVIBOND SL-Hi | UVIFILL SL-Tx | UVBOND SL-Clear-Hi | UVFORM SL | APTEK Repair Resi